You are not logged in.
For Calliban re #300
The NewMars forum is a great place for a report of a project such as this one! If you decide the material would make an article suitable for a publication, you have everything you need assembled and readily accessible. There are numerous categories into which this project would be a good fit.
(th)
Offline
Like button can go here
For Calliban re Geosynchronous orbit...
Thank you for that bold vision in https://newmars.com/forums/viewtopic.ph … 55#p233755
If you have a moment, please add the circumference to be joined. By coincidence, I've been working on a way of dealing with challenges of gas gun launch in the Air Capture topic, and one of the variations would use pipes of modest diameter. I wonder what stresses would act upon a chain of pipes at GEO. The mass of satellites that clamp on would tend to pull the pipe out of true, and the Sun would heat the pipe while cold of space in shadow would cause it to contract. That would be an interesting engineering challenge.
(th)
Offline
Like button can go here
For Calliban re wind tower... https://newmars.com/forums/viewtopic.ph … 27#p233827
Thanks for showing us your project in stages! Congratulations on your progress so far, and I hope the final installation goes smoothly.
The rope drive concept surely has ancient heritage.
Will it have an idler wheel to take up slack when the rope stretches?
(th)
Offline
Like button can go here
My plan was to mount the lower pulley and clutch on long bolts, which would be tightened to adjust the tension. However, an idler pulley may work better, as it would allow the clutch to remain at constant height. This woukd make interface with tools much easier. I may modify the design to include an idler wheel.
"Plan and prepare for every possibility, and you will never act. It is nobler to have courage as we stumble into half the things we fear than to analyse every possible obstacle and begin nothing. Great things are achieved by embracing great dangers."
Offline
Like button can go here
For Calliban re #304
Thank you for considering the idler pulley idea. That wheel and axle will consume a part of the energy you are transferring, so there is a tradeoff with convenience. How would a Dutch craftsman have dealt with this?
Come to think of it, are there any examples of this situation still running? Your mill is smaller than the ones you showed us from your trip, so it may not be possible/reasonable to make a direct comparison. However, it ** is ** fun for us to watch a modern craftsman dealing (once again) with problems of mechanical energy capture systems.
(th)
Offline
Like button can go here
For Calliban re progress with wind tower...
http://newmars.com/forums/viewtopic.php … 84#p233884
Thanks for showing this important moment in the life of the new mill. And thanks for the link to a resource about 19th century wind mills. It seems to me (memory is vague) that GW Johnson might have written about experience with a wind mill in Texas. Wind mills in that country would have been dedicated to pulling water up from deep reservoirs. Efficiency might not have been top-of-mind for those builders.
(th)
Offline
Like button can go here
For Calliban re link to history of wind mills in Nebraska and region...
https://core.ac.uk/download/17270953.pdf
It is a pleasure to read this document by a remarkable gent: Erwin Hinckley Barbour ...
His modesty and courtesy are refreshing in the modern age.... The many examples of successful home made wind devices are inspiring.
I don't have time to read the entire document now, but will remember it for when there might be an hour or so that can be invested,
It seems to me your design would have made an entry in the collection, if it had been available.
The most expensive machine cost $150 in 1899. According to Google, that is equivalent to about $5.688 today, which would represent a significant investment for most Americans these days. I can see why it was described as it was. The author made much of the mills that cost nothing because they were constructed from old wood and components. A wagon wheel mounted on a barn caught my eye. Pretty clever, for South facing winds.
(th)
Offline
Like button can go here
TH, yes indeed. Wood is a low embodied energy material that is often recycled. In my case, the wood that I used to make the machine would otherwise have been cut into firewood. When the machine reaches the end of its life, the wood will fulfill that purpose once again. The same can probably be said of the various machines listed in the book.
I used other materials in my machine. Screws, bearings, steel strap, epoxy glue, oil based paint, polymer rope and aluminium for the blades. Still, I estimate that wood is 90% of total mass. My device cost me around $300 in parts and a good deal of time. Still, that is free time that I otherwise would have wasted watching reruns of old scifi.
Could I have reduced the the input of non-wood materials with additional effort? Yes. It would have taken more time and carefull design.
I estimate that the mill will raise about 2000kWh of mechanical work each year. Over a 15 year life, that amounts to 30,000kWh, or $0.01/kWh. Much cheaper than the $0.3/kWh that is the insane cost of electricity in the UK. If I put a price on my time, then the savings would be lower. But everyone needs a hobby. A hobby that makes or saves money is always a good thing.
"Plan and prepare for every possibility, and you will never act. It is nobler to have courage as we stumble into half the things we fear than to analyse every possible obstacle and begin nothing. Great things are achieved by embracing great dangers."
Offline
Like button can go here
For Calliban! First, thanks for your reply in Post #308
Your mill may not be given responsibility to water the orchard, but I still think it would have merited a mention. In fact, unless I miss my guess, it still ** does ** potentially fit into modern low tech off-grid periodicals.
This post is about your contribution to the new thermodynamics topic. I am really flying blind here, so appreciate your feedback!
https://newmars.com/forums/viewtopic.ph … 12#p233912
The entire history of this inquiry is recorded in the archive, but I wasn't expecting anyone to actually read it.
To my surprise, offtherocks turned out to be a computer guru who can run Python the way most folks run Excell or Word.
The history of the inquiry is divided between the Python topic and the Harvest topic where results are shown.
So the answer to your question is ... no! Neither of us thought about plasma, because at the beginning of the inquiry, I just wanted to see if there is any potential value to collecting atmosphere on the way up. It turns out that a ton of air is worth millions of USD at Falcon 9 rates.
I don't think we are ultimately going to pull this off, and you may have spotted a hurdle we can't overcome.
The major engineering problem I was aware of is the need to put a cap over the tubes when the air pressure inside the tube matches the pressure of the oncoming air. Your observation about the air turning into plasma is certainly helpful at this point, though this situation is a bit different than air flowing past a heat sheild as we have seen in Starship tests thanks to the SpaceX imagery from flight.
I think that a CFD package such as OpenFOAM could probably do a better job of modeling this scenario, but Gemini seems to think Python can handle it. I'm just along for the ride.
The reason for the new thermodynamics topic is precisely the fact that Gemini was (is) struggling with the thermodynamics of the Air Capture scenario.
So! Thanks again for you feedback!
(th)
Offline
Like button can go here
It might work better for a lower stage, which would presumably have a lower peak velocity. At 2km/s, the incoming air will carry some 2MJ/kg of kinetic energy. That much heating is more manageable via regenerative cooling and is beneath dissociation temperatures, which start to become significant at temperature >2500°C. Boosting an upper stage to say 2km/s at 30km seperation height would greatly improve payload capacity.
"Plan and prepare for every possibility, and you will never act. It is nobler to have courage as we stumble into half the things we fear than to analyse every possible obstacle and begin nothing. Great things are achieved by embracing great dangers."
Offline
Like button can go here
For Calliban re #310
One of the (many) advantages of an open forum like this is the opportunity to pick up insights that are not available otherwise.
Thanks for your observations about this capture idea at a lower velocity.
I'll tuck the idea for retrieval later.
(th)
Offline
Like button can go here
For Calliban re post about light gas gun launcher....
https://newmars.com/forums/viewtopic.ph … 24#p233924
Thank you for your observation and question. I'm not in a position to answer, except that your observation certainly make sense.
What I ** can ** report is that (as I expected) the simulation shows that drag steals a substantial part of the momentum of the projectile as it ascends. Anyone can run the various Python versions. I've tried to document the changes as we've made them, and i removed the one version that failed altogether.
In a typical run, the projectile can make 100 km and still have some momentum/velocity left. It is at that altitude (or thereabouts) that the solid rocket motor would ignite to curve the projectile over to an ellipse perigee above the atmosphere. A second burn would be required to even things out. The test program assumes 1/3 for the air capture device/nose cone, 1/3 for the payload compartment and control electronics, and 1/3 for the circularization rocket.
What the simulation seems to show is that capturing air on the way up helps to improve performance, because the work done to accelerate the gas to the projectile velocity is less than the drag that would be encountered otherwise. Unfortunately, the benefit is not of long duration, because the capture container fills up so quickly, as measured by the pressure inside the container matching the pressure of the atmosphere ahead of the projectile. Never-the-less, at this point, the simulation seems to show that about a ton of air can be captured and delivered to LEO as a commodity that can be traded.
If this concept would actually work in the Real Universe is quite another matter.
(th)
Offline
Like button can go here
For Calliban .... to my surprise, Gemini invited you to assist if you might have time...
I reported the results of the test run, and your observations... I think Gemini is struggling with this problem. I know I would be.
Hello Again! Our mechanical engineer took an interest in the data generated by our little study program, which I will upload in a moment. He asked about the plasma state of the gas, which he said seems likely at the temperatures the Python program is calculating. He also added notes about the kinetic energy imparted to the gas and computed a figure that he thought might be in play. I believe your program is already attempting to calculate the energy flows. I don't see having the gas in a plasma state is being advantageous. Here is a quote. I appended a Google lookup for alloy vs temperature ...
python3 20250828ThermodynamicsStudyV01.py
--- Thermal Model Test ---
Number of Pipes: 66
Total Cooling Surface Area: 1500.00 m^2
Initial Pipe Temp: 100.00 K
Initial Gas Temp: 288.00 K
--------------------------
Time: 0.00s | Gas Temp: 59775.22 K | Pipe Temp: 200.17 K | Mass: 105.83 kg
Time: 0.01s | Gas Temp: 59776.32 K | Pipe Temp: 299.81 K | Mass: 211.66 kg
Time: 0.02s | Gas Temp: 59777.09 K | Pipe Temp: 399.17 K | Mass: 317.50 kg
Time: 0.03s | Gas Temp: 59777.71 K | Pipe Temp: 498.31 K | Mass: 423.33 kg
Time: 0.04s | Gas Temp: 59778.25 K | Pipe Temp: 597.25 K | Mass: 529.16 kg
Time: 0.05s | Gas Temp: 59778.74 K | Pipe Temp: 696.00 K | Mass: 634.99 kg
Time: 0.06s | Gas Temp: 59779.20 K | Pipe Temp: 794.57 K | Mass: 740.83 kg
Time: 0.07s | Gas Temp: 59779.64 K | Pipe Temp: 892.97 K | Mass: 846.66 kg
Time: 0.08s | Gas Temp: 59780.06 K | Pipe Temp: 991.19 K | Mass: 952.49 kg
Time: 0.09s | Gas Temp: 59780.47 K | Pipe Temp: 1089.24 K | Mass: 1058.32 kg
Time: 0.10s | Gas Temp: 59780.87 K | Pipe Temp: 1187.12 K | Mass: 1164.16 kg
Time: 0.11s | Gas Temp: 59781.27 K | Pipe Temp: 1284.84 K | Mass: 1269.99 kg
Time: 0.12s | Gas Temp: 59781.65 K | Pipe Temp: 1382.39 K | Mass: 1375.82 kg
Time: 0.13s | Gas Temp: 59782.03 K | Pipe Temp: 1479.77 K | Mass: 1481.65 kg
Time: 0.14s | Gas Temp: 59782.41 K | Pipe Temp: 1576.99 K | Mass: 1587.49 kg
Time: 0.15s | Gas Temp: 59782.79 K | Pipe Temp: 1674.04 K | Mass: 1693.32 kg << 1643 Kelvin steel alloy melting point see Google below
Time: 0.16s | Gas Temp: 59783.16 K | Pipe Temp: 1770.93 K | Mass: 1799.15 kg
Time: 0.17s | Gas Temp: 59783.52 K | Pipe Temp: 1867.65 K | Mass: 1904.98 kg
Time: 0.18s | Gas Temp: 59783.89 K | Pipe Temp: 1964.21 K | Mass: 2010.82 kg
Time: 0.19s | Gas Temp: 59784.25 K | Pipe Temp: 2060.62 K | Mass: 2116.65 kg
Time: 0.20s | Gas Temp: 59784.61 K | Pipe Temp: 2156.85 K | Mass: 2222.48 kg
Time: 0.21s | Gas Temp: 59784.97 K | Pipe Temp: 2252.93 K | Mass: 2328.31 kg
Time: 0.22s | Gas Temp: 59785.33 K | Pipe Temp: 2348.85 K | Mass: 2434.15 kg
Time: 0.23s | Gas Temp: 59785.69 K | Pipe Temp: 2444.60 K | Mass: 2539.98 kg
Time: 0.24s | Gas Temp: 59786.04 K | Pipe Temp: 2540.20 K | Mass: 2645.81 kg
Time: 0.25s | Gas Temp: 59786.39 K | Pipe Temp: 2635.64 K | Mass: 2751.64 kg
Time: 0.26s | Gas Temp: 59786.75 K | Pipe Temp: 2730.91 K | Mass: 2857.47 kg
Time: 0.27s | Gas Temp: 59787.10 K | Pipe Temp: 2826.03 K | Mass: 2963.31 kg
Time: 0.28s | Gas Temp: 59787.45 K | Pipe Temp: 2920.99 K | Mass: 3069.14 kg
Time: 0.29s | Gas Temp: 59787.80 K | Pipe Temp: 3015.79 K | Mass: 3174.97 kg
Time: 0.30s | Gas Temp: 59788.14 K | Pipe Temp: 3110.43 K | Mass: 3280.80 kg
Time: 0.31s | Gas Temp: 59788.49 K | Pipe Temp: 3204.92 K | Mass: 3386.64 kg
Time: 0.32s | Gas Temp: 59788.84 K | Pipe Temp: 3299.24 K | Mass: 3492.47 kg
Time: 0.33s | Gas Temp: 59789.18 K | Pipe Temp: 3393.41 K | Mass: 3598.30 kg
Time: 0.34s | Gas Temp: 59789.53 K | Pipe Temp: 3487.43 K | Mass: 3704.13 kg
Time: 0.35s | Gas Temp: 59789.87 K | Pipe Temp: 3581.28 K | Mass: 3809.97 kg
Time: 0.36s | Gas Temp: 59790.22 K | Pipe Temp: 3674.98 K | Mass: 3915.80 kg
Time: 0.37s | Gas Temp: 59790.56 K | Pipe Temp: 3768.52 K | Mass: 4021.63 kg
Time: 0.38s | Gas Temp: 59790.90 K | Pipe Temp: 3861.91 K | Mass: 4127.46 kg
Time: 0.39s | Gas Temp: 59791.24 K | Pipe Temp: 3955.14 K | Mass: 4233.30 kg
Time: 0.40s | Gas Temp: 59791.58 K | Pipe Temp: 4048.22 K | Mass: 4339.13 kg
Time: 0.41s | Gas Temp: 59791.92 K | Pipe Temp: 4141.14 K | Mass: 4444.96 kg
Time: 0.42s | Gas Temp: 59792.26 K | Pipe Temp: 4233.91 K | Mass: 4550.79 kg
Time: 0.43s | Gas Temp: 59792.60 K | Pipe Temp: 4326.52 K | Mass: 4656.63 kg
Time: 0.44s | Gas Temp: 59792.94 K | Pipe Temp: 4418.98 K | Mass: 4762.46 kg
Time: 0.45s | Gas Temp: 59793.28 K | Pipe Temp: 4511.28 K | Mass: 4868.29 kg
Time: 0.46s | Gas Temp: 59793.61 K | Pipe Temp: 4603.44 K | Mass: 4974.12 kg
Time: 0.47s | Gas Temp: 59793.95 K | Pipe Temp: 4695.43 K | Mass: 5079.96 kg
Time: 0.48s | Gas Temp: 59794.29 K | Pipe Temp: 4787.28 K | Mass: 5185.79 kg
Time: 0.49s | Gas Temp: 59794.62 K | Pipe Temp: 4878.97 K | Mass: 5291.62 kg
Time: 0.50s | Gas Temp: 59794.96 K | Pipe Temp: 4970.51 K | Mass: 5397.45 kg
Time: 0.51s | Gas Temp: 59795.29 K | Pipe Temp: 5061.90 K | Mass: 5503.28 kg
Time: 0.52s | Gas Temp: 59795.63 K | Pipe Temp: 5153.13 K | Mass: 5609.12 kg
Time: 0.53s | Gas Temp: 59795.96 K | Pipe Temp: 5244.21 K | Mass: 5714.95 kg
Time: 0.54s | Gas Temp: 59796.29 K | Pipe Temp: 5335.15 K | Mass: 5820.78 kg
Time: 0.55s | Gas Temp: 59796.63 K | Pipe Temp: 5425.93 K | Mass: 5926.61 kg
Time: 0.56s | Gas Temp: 59796.96 K | Pipe Temp: 5516.56 K | Mass: 6032.45 kg
Time: 0.57s | Gas Temp: 59797.29 K | Pipe Temp: 5607.04 K | Mass: 6138.28 kg
Time: 0.58s | Gas Temp: 59797.62 K | Pipe Temp: 5697.36 K | Mass: 6244.11 kg
Time: 0.59s | Gas Temp: 59797.95 K | Pipe Temp: 5787.54 K | Mass: 6349.94 kg
Time: 0.60s | Gas Temp: 59798.28 K | Pipe Temp: 5877.57 K | Mass: 6455.78 kg
Time: 0.61s | Gas Temp: 59798.61 K | Pipe Temp: 5967.45 K | Mass: 6561.61 kg
Time: 0.62s | Gas Temp: 59798.94 K | Pipe Temp: 6057.18 K | Mass: 6667.44 kg
Time: 0.63s | Gas Temp: 59799.27 K | Pipe Temp: 6146.76 K | Mass: 6773.27 kg
Time: 0.64s | Gas Temp: 59799.60 K | Pipe Temp: 6236.19 K | Mass: 6879.11 kg
Time: 0.65s | Gas Temp: 59799.93 K | Pipe Temp: 6325.47 K | Mass: 6984.94 kg
Time: 0.66s | Gas Temp: 59800.26 K | Pipe Temp: 6414.61 K | Mass: 7090.77 kg
Time: 0.67s | Gas Temp: 59800.58 K | Pipe Temp: 6503.59 K | Mass: 7196.60 kg
Time: 0.68s | Gas Temp: 59800.91 K | Pipe Temp: 6592.43 K | Mass: 7302.44 kg
Time: 0.69s | Gas Temp: 59801.24 K | Pipe Temp: 6681.12 K | Mass: 7408.27 kg
Time: 0.70s | Gas Temp: 59801.56 K | Pipe Temp: 6769.66 K | Mass: 7514.10 kg
Time: 0.71s | Gas Temp: 59801.89 K | Pipe Temp: 6858.06 K | Mass: 7619.93 kg
Time: 0.72s | Gas Temp: 59802.21 K | Pipe Temp: 6946.31 K | Mass: 7725.77 kg
Time: 0.73s | Gas Temp: 59802.54 K | Pipe Temp: 7034.41 K | Mass: 7831.60 kg
Time: 0.74s | Gas Temp: 59802.86 K | Pipe Temp: 7122.37 K | Mass: 7937.43 kg
Time: 0.75s | Gas Temp: 59803.19 K | Pipe Temp: 7210.17 K | Mass: 8043.26 kg
Time: 0.76s | Gas Temp: 59803.51 K | Pipe Temp: 7297.84 K | Mass: 8149.09 kg
Time: 0.77s | Gas Temp: 59803.83 K | Pipe Temp: 7385.36 K | Mass: 8254.93 kg
Time: 0.78s | Gas Temp: 59804.16 K | Pipe Temp: 7472.73 K | Mass: 8360.76 kg
Time: 0.79s | Gas Temp: 59804.48 K | Pipe Temp: 7559.96 K | Mass: 8466.59 kg
Time: 0.80s | Gas Temp: 59804.80 K | Pipe Temp: 7647.04 K | Mass: 8572.42 kg
Time: 0.81s | Gas Temp: 59805.12 K | Pipe Temp: 7733.98 K | Mass: 8678.26 kg
Time: 0.82s | Gas Temp: 59805.45 K | Pipe Temp: 7820.77 K | Mass: 8784.09 kg
Time: 0.83s | Gas Temp: 59805.77 K | Pipe Temp: 7907.42 K | Mass: 8889.92 kg
Time: 0.84s | Gas Temp: 59806.09 K | Pipe Temp: 7993.92 K | Mass: 8995.75 kg
Time: 0.85s | Gas Temp: 59806.41 K | Pipe Temp: 8080.28 K | Mass: 9101.59 kg
Time: 0.86s | Gas Temp: 59806.73 K | Pipe Temp: 8166.50 K | Mass: 9207.42 kg
Time: 0.87s | Gas Temp: 59807.05 K | Pipe Temp: 8252.58 K | Mass: 9313.25 kg
Time: 0.88s | Gas Temp: 59807.37 K | Pipe Temp: 8338.51 K | Mass: 9419.08 kg
Time: 0.89s | Gas Temp: 59807.68 K | Pipe Temp: 8424.30 K | Mass: 9524.92 kg
Time: 0.90s | Gas Temp: 59808.00 K | Pipe Temp: 8509.94 K | Mass: 9630.75 kg
Time: 0.91s | Gas Temp: 59808.32 K | Pipe Temp: 8595.45 K | Mass: 9736.58 kg
Time: 0.92s | Gas Temp: 59808.64 K | Pipe Temp: 8680.81 K | Mass: 9842.41 kg
Time: 0.93s | Gas Temp: 59808.96 K | Pipe Temp: 8766.03 K | Mass: 9948.25 kg
Time: 0.94s | Gas Temp: 59809.27 K | Pipe Temp: 8851.11 K | Mass: 10054.08 kg
Time: 0.95s | Gas Temp: 59809.59 K | Pipe Temp: 8936.04 K | Mass: 10159.91 kg
Time: 0.96s | Gas Temp: 59809.90 K | Pipe Temp: 9020.84 K | Mass: 10265.74 kg
Time: 0.97s | Gas Temp: 59810.22 K | Pipe Temp: 9105.49 K | Mass: 10371.58 kg
Time: 0.98s | Gas Temp: 59810.54 K | Pipe Temp: 9190.01 K | Mass: 10477.41 kg
Time: 0.99s | Gas Temp: 59810.85 K | Pipe Temp: 9274.38 K | Mass: 10583.24 kg
Per Google:
There is no single "best possible alloy" of steel, as "best" depends on the application, but typical steel alloys have a melting range between approximately 1370°C and 1530°C, which is about 1643 K to 1803 K. The specific melting point varies significantly based on the different alloying elements like carbon, nickel, manganese, and chromium, which can raise or lower the temperature at which the steel transitions from solid to liquid.
***
That's an excellent analysis from your engineer. He is absolutely right on both counts: the gas would be in a plasma state at those temperatures, and the melting point of the pipe is a critical factor we need to consider. This is a very valuable feedback.
Analysis of the Thermal Model
The output from the "Thermodynamics Study" program reveals a significant flaw that we've been circling.Plasma State: Your engineer is correct. A temperature of ~60,000 K is so high that it is well into the plasma regime. We are trying to model the behavior of a gas at these temperatures using the ideal gas law and a constant specific heat, which is completely invalid for a plasma. The energy required to strip electrons from atoms (ionization) is immense. This energy is a major sink that our current model is completely ignoring. The absurdly high temperatures are a result of taking all the kinetic energy and converting it to thermal energy without accounting for the energy consumed by the ionization process.
The Melting Pipe: You've highlighted a critical observation from the 0.15s mark. At a temperature of 1674.04 K, the pipe has already exceeded the typical melting point of steel alloys (1643 K). This means that even if our gas temperature model was working, the entire pipe structure would be molten in a fraction of a second, rendering the entire system useless. The pre-cooling of the pipe is being overwhelmed by the massive influx of energy.
Moving Forward
Our model is still fundamentally broken. The core problem is that our simple heat_transferred calculation is insufficient. We need to do "bookkeeping" not just for heat, but for the state change of the gas itself.In the next iteration, we'll revise the thermal model to account for the energy of ionization. This will act as a "thermal buffer," absorbing a large portion of the kinetic energy from the incoming air. This will reduce the calculated temperature of the gas to a much more physically plausible level.
Please share your engineer's specific calculations for the kinetic energy in our next session. We will use that to create a more accurate energy budget for the system, which will allow us to build a more robust and realistic simulation.
(th)
Offline
Like button can go here
For Calliban re wind project: https://newmars.com/forums/viewtopic.ph … 06#p234006
Congratulations on finishing construction of the main body of the system.
The braces look worthy of even the most vigorous winter wind.
Installation of the power transfer subsystem will be of interest.
Sorry to hear of the loss of the trees. They are welcome additions to the urban landscape (when healthy).
(th)
Offline
Like button can go here
For Calliban re update on wind machine: https://newmars.com/forums/viewtopic.ph … 28#p234028
Congratulations on adding the power transfer subsystem!
It seems to me this might be regarded as Version 1 of a series.
Rope is a term that covers a wide range, so your readers cannot know the mass of the rope you've chosen, but fishing line might be strong enough for this application and it is very light in even strong sizes.
How to arrange to insure a grip on the tumbler rotor would be a question.
It will be interesting to see the images of the system working, even if you have not yet seen the full force of winds that I expect winter will bring.
(th)
Offline
Like button can go here
For Calliban re completed machine! https://newmars.com/forums/viewtopic.ph … 41#p234041
Congratulations on carrying this project from start to finish, and for sharing your vision and progress with this community, and with the larger readership of the forum we cannot measure but hope exists.
A detail that might of of interest to those who work a bit with rope, is how you achieved the splice to pass smoothly over the pulleys. The traditional method of intertwined lines takes some time, but the long splice can pass through a pulley.
Here is a YouTube video Google found, showing the construction of a long splice. Mark the braider shows how to use a special tool designed for the purpose. https://www.youtube.com/watch?v=0QA5NW6SQOk
The video is for our readers, of course, with the thought you might have done something similar.
(th)
Offline
Like button can go here
For Calliban re rope fusion join ... https://newmars.com/forums/viewtopic.ph … 47#p234047
Congratulations on making that work!
I noticed the rope looked as though it might have plastic material... That should handle moisture well. However, I didn't think of heat binding and appreciate your telling us of your success with that method.
If you'll indulge a further inquiry ... are you planning to put rollers where the rope appears to rub against the platform at the top of the tower, under the mill?
(th)
Offline
Like button can go here
For Calliban re 100 year old pulleys !!! https://newmars.com/forums/viewtopic.ph … 58#p234058
Thanks for this delightful anecdote, and for the testimonial to tried-and-true technology!
It will be good to hear reports when you have sufficient wind to turn the mill. I do have a follow up question, but it is on the curiosity side ... I couldn't help but notice the similarity of your blade design to propellers, in contrast to the huge wind catch surfaces of so many of the examples in the book you showed us. There is probably a good reason for this design choice, starting with the observation that you are working in 2025 with the benefit of modern knowledge.
(th)
Offline
Like button can go here
For Calliban re Centripetal force...
https://newmars.com/forums/viewtopic.ph … 73#p234073
It seems you may be reliving the trial-by-winds that your countless predecessors have faced for thousands of years. GW Johnson talks often about the knowledge of engineering that is never written down, but which only lives briefly in the minds of the practitioners.
The difference today is that you have a medium through which you are able to share your discoveries.
Thank you for telling us of the disappointing failure mode that showed up so soon after "first wind".
(th)
Offline
Like button can go here
For Calliban re downdraft concept: https://newmars.com/forums/viewtopic.ph … 99#p234099
First, thanks for telling us of your (tentative) plans for Version 2 of the wind device!
Second, thanks for describing a downdraft tower.
I'm reminded of the onshore and offshore winds reported for some coastal regions.
The operating cycle of the downdraft chimney would be interesting to see. It will take energy to transport water from the ground (or below ground in some cases) up to the top of the tower. That energy should be at least partially recoverable as the water laden air descends. What I'm not yet clear on is the source of the energy that will be needed to operate the turbine to collect energy from the moving air.
I wonder if the power you are describing is similar to a tornado, which achieves tremendous power production as a layer of cold air flows over a layer of hot air. We do not currently have anyone in the group who admits to knowing how to create animation. I've done a couple of simple animations with Blender, so I'm familiar with the technique of creating images that differ slightly from one to the next, but which create the illusion of motion when played successively. Our brains interpolate between images.
In this case, the images might show cold air at the top of the chimney flowing down due to greater density and the presence of water droplets. What I'm not yet clear on is whether the flow would continue once started, or if a continuous injection of water is needed.
The weather conditions at a site are also of interest. I'm wondering if this system would depend upon favorable weather conditions, such that it might work only at certain times of the day, or perhaps other influences might be at work.
***
Speaking of wind ... I recently reported on a kite that apparently was tested in Ireland to generate power. The machine (as I understand it) was able to produce power on the down leg of a cycle. Apparently the kite pulled on a cord when broadside to the wind, and was able to return to the starting point by changing aspect and gliding into the wind. Apparently the system has been tested with success, and (this is possibly of special interest) it was able to survive storm conditions, when other power generation systems were knocked offline.
If those reports are accurate, then the kite designers would have solved some interesting control problems. With modern technology, there might be wireless communication between the onboard flight controller and the ground, so that modern powerful (small) computers could manage sensor data to create appropriate steering commands for the kite.
All of this ** must ** be happening for the system to have survived storm conditions.
The system (as I recall the article) includes battery storage, which builds up when the kite is playing out, and draws down when the kite is returning, because the cable has to be pulled in. Apparently the net effect is accumulation of energy that can be delivered to customers.
I asked Google "kite in Ireland that generates power" and it came back with quite a list of citations, starting with:
Dutch company Kite power has been testing its system since September 2023 in Bangor Erris, a remote area in Ireland's western coast. The innovation works by connecting a 60-square-meter kite to a generator on the ground through a cable.
(th)
Offline
Like button can go here
For Calliban re Vision of Deep Space Gravitational Sensing... https://newmars.com/forums/viewtopic.ph … 01#p234101
I like the vision you have described on multiple levels.
It will take a long lived government to pull off a project like that. A realistic concept might be an AI powered "government" that is set up to perform just such data gathering. We already have hints of what such systems might look like, in the highly automated networks of communications satellites already in orbit, along with numerous scientific sensor networks.
the key element not currently demonstrated is self-replication. Once AI sensor collection systems become capable of replicating themselves, they should be able to expand into the entire solar system.
Update: May I tag along with your vision a bit? I would like to see every free flying object in the solar system fitted with a transponder. This will take a while, but it fits in nicely with your vision of trillions of gravity sensors.
Another application of the system you have proposed is solar system defense... A clever alien might be able to enter the system undetected in ordinary radiation, but they aren't likely to be able to avoid bending space time due to their mass, so a detection system on the scale of your vision should be able to not only detect them, but more importantly, detect the ** absence ** of signature in the electromagnetic spectrum.
(th)
Offline
Like button can go here