New Mars Forums

Official discussion forum of The Mars Society and MarsNews.com

You are not logged in.

Announcement

Announcement: This forum is accepting new registrations by emailing newmarsmember * gmail.com become a registered member. Read the Recruiting expertise for NewMars Forum topic in Meta New Mars for other information for this process.

#351 2024-07-29 01:18:20

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

As a follow up, I gave the suggestions from Gemini to ChatGPT4o, and it came back with a detailed set of specifications to create a complete web site to support the basic orbital mechanics course GW Johnson is offering via our forum.

I have saved the suggestions from ChatGPT4o, and expect to have time to work on them in August.

According to Gemini, there are ** no ** sites on record that implement the vision of animation of GW Johnson's work.

It would appear this would be a worthwhile undertaking.

(th)

Offline

#352 2024-07-29 08:45:34

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Responding to the question about the definition of "impulsive".  It is a "fuzzy" thing.  But here is what I recommend.

"Impulsive" burns need to approximate instantaneous velocity changes,  in the sense that (1) the radius from central body center does not change during the burn by more than something like 1 part in a thousand,  and/or (2) the burn time is under about 5 parts in a hundred the duration of the orbital period.  As a rule-of-thumb for lower Earth orbits,  the vehicle should accelerate faster than 0.1 or 0.2 gees,  preferably nearer 0.5 gees.

The first criterion prevents the added energy from partitioning into potential energy instead of kinetic energy,  which is gravity loss.  The second criterion is more of a practical thing.  An "impulsive" burn at perigee or apogee of an orbit with a period near 90 minutes needs to occur within a single handful of minutes,  to stay "near" that perigee or apogee. 

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#353 2024-07-29 09:08:30

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Not sure where to put these.  From AIAA’s “Daily Launch” for Monday 7-29-2024:

Debris survives reentry:
AVIATION WEEK NETWORK
SpaceX To Shift Dragon Splashdowns To West Coast

In an effort to stem the chance that debris from discarded Dragon capsule trunk sections could reenter over populated areas, SpaceX will shift splashdown and recovery operations to the West Coast, the company said July 26. The decision follows the recovery of a piece of Dragon debris in Australia in 2022, indicating that—contrary to computer modeling—parts of the capsule’s discarded trunk can survive reentry heating.

My take on it:  I have pointed out for years now that virtually nothing actually "burns up" on re-entry.  Debris WILL make it through and crash to the surface,  somewhere.  Even from very insubstantial construction.  Example:  the Australians said they picked up about 75 tons of debris from Skylab that crashed in 1979 upon western Australia.  Skylab was said by NASA to be about 85-90 tons at its entry.  Not much at all burned up!  Despite its shell being an aluminum S-IV Saturn stage. 
------- 
The end of Atlas-5:
SPACENEWS
ULA prepares for final military launch of Atlas 5 rocket

United Launch Alliance (ULA) is set to launch its final Atlas 5 rocket for the U.S. military on July 30. The classified payload, designated USSF-51, is scheduled to lift off at 6:45 a.m. Eastern from Space Launch Complex 41 at Cape Canaveral Space Force Station, bound for geostationary Earth orbit. 


GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#354 2024-07-29 11:31:36

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson re #352

Thanks for details about planning for "impulsive" burns at perigee or apogee...

From the sounds of things, ChatGPT4o's default of 60 seconds is reasonable.

Thanks too, for mention of the G force produced by the burn. I had not thought that far ahead, so appreciate the reminder.

I'm looking forward to seeing if the tips provided by ChatGPT4o for a web based animation of your course material is something I can pull off.

What I am imagining is an interaction where the student can set up each burn at perigee or apogee, click "go" and watch the simulated spacecraft complete the next orbit.  I'm hoping we can persuade the software to show the equations and the numbers as they drive the animation.

(th)

Offline

#355 2024-08-01 18:42:13

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

This post is for Void and anyone else in our membership who might be willing to tackle Rocket Science if the pathway is made simple enough. GW Johnson heard my comparison of his existing work to like an F16, when his audience is just barely able to fly a Cessna 150.

In the PDF at the link below, GW has attempted to prepare the reader to use the Basic Orbits spreadsheet, by introducing individual cells, and describing procedures to follow to obtain interesting and useful results.

Void, GW is continuing to praise your creative idea of building landing ring/cushions to fit around the Starship to achieve a successful vertical landing on an unprepared surface.  This idea may be patentable, but at $1000 to request a preliminary reservation to request a patent, and $5,000 for the most basic of patents, it is unlikely you or I will attempt it. However, GW has already placed multiple patents on record. One was his alone, and the rest were team efforts.

I would like to invite you to at least look at this peace offering from GW, to see if you might be able to build up a head of steam to tackle it. If you ** are ** willing to tackle it, I would be a willing classmate, and potentially we might enlist one more member. Who that might be I have no idea, but certainly with 1000 members of record the potential that one would like to participate is non-zero.

SpaceNut... please keep upgrading all those innocent "banned" members to InActive status as rapidly as you have time.  Every "banned" member who is not upgraded is lost to us. Who would make the effort to contact this forum, if the member finds he or she has been banned? They have no way of knowing the "banning" was an emergency measure to defeat hackers.

https://www.dropbox.com/scl/fi/icrjpdez … mx4yd&dl=0

Above is a link to: User Manual for Orbit Basics Excel Spreadsheet.

For GW ... please find a link to the spreadsheet and send it via email or by a post in this topic, so I can add it to this post.

The version of the orbits spreadsheet that the manual was written for is located at the link below,  which was copied from post #20 in the "orbital mechanics class traditional" thread under "interplanetary transportation",  in the Acheron labs" section. --  GW

https://www.dropbox.com/scl/fi/cxtpsx2n … nmkmv&dl=0

PS - I tested the link,  it works.

The next step is for one or more members of NewMars forum to follow the links and begin study of the material.

In case there is someone not currently enrolled as a member, if you would like to take part in this initiative, please see the Recruiting topic for procedure.

(th)

Offline

#356 2024-08-02 07:59:58

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

The version of the orbits spreadsheet that the manual was written for is located at the link below,  which was copied from post #20 in the "orbital mechanics class traditional" thread under "interplanetary transportation",  in the Acheron labs" section. --  GW

https://www.dropbox.com/scl/fi/cxtpsx2n … nmkmv&dl=0

PS - I tested the link,  it works.

Last edited by GW Johnson (2024-08-02 08:01:17)


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#357 2024-08-03 07:57:17

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson re Void's Invention of Doughnut lander cargo concept...

In correspondence and here in the forum, you have indicated Void's idea would appear to be worth serious consideration for a lunar landing of a tall thin spaceship such as Starship.  The design of a doughnut shaped cargo carrier to be fitted to a Starship after it reaches Earth Orbit would include a means of attaching the carrier firmly to the Starship, so that it will remain in place during burns, and more importantly, will be able to sustain the forces that would be imposed upon it by the Starship if the regolith was uneven at a landing site.

***
In a separate correspondence, or perhaps in a post, you indicated that at first glance, you did not think Void's idea would be as useful on Mars. I would like to offer an alternative way of looking at Void's idea for Mars...

The doughnut shape might lend itself to a useful function as part of aerobraking maneuver, since the cross sectional area of the combined ship and doughnut would be much greater than that of the Starship alone.

In saying that, I recognize your many times repeated caution that the atmosphere of Mars is so slim the accuracy of navigation to achieve aerobraking without missing the planet entirely, or plowing into the surface is ** very ** difficult to achieve.

However, Void's idea has one ** very ** significant benefit for Mars...

If we go with your recommended landing method of direct retro-propulsion, then moving cargo out of the Starship (or other vehicle such as your design) and into the cargo doughnut means the rocket can be loaded with more propellant, and that propellant can assist with landing and provide for return to orbit.

(th)

Offline

#358 2024-08-03 09:32:03

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Aside from the large deceleration forces that lead to large forces in the members connecting the doughnut to the main vehicle,  there is a serious and very-fatal shock impingement heating risk.  The doughnut,  and the members that secure it,  plus the main vehicle,  all shed bow shock waves during hypersonic entry.  Doesn't matter which way the thing faces.  If any of those shock waves impinge upon any adjacent structure,  that adjacent structure overheats to destruction in a matter of a single handful of seconds,  max.

This effect has been known since the Mach 6.7 flight of the X-15A-2 back about 1968.  It is EXACTLY why no successful entry vehicle has EVER had parallel-mounted nacelles of any kind.  It is EXACTLY why no hypersonic aircraft will ever resemble the layout of the SR-71.  And id it EXACTLY why the Skylon airframe concept cannot survive entry without massive changes.

The doughnut concept makes a whole lot more sense for the airless moon,  not very much for Mars,  whose thin atmosphere is enough to cause severe hypersonic heating at orbital entry speeds. 

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#359 2024-08-03 10:05:21

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

for GW Johnson re #358

Thanks for helping us take a step forward to visualize Void's doughnut shaped cargo carrier.

As I read your text, you are thinking about the doughnut mounted on the exterior of the rocket hull without a shield of any kind.

That is exactly appropriate for a Lunar or other airless body landing.  The rigging in that case has to be strong enough to hold up against force exerted by the hull if the regolith is uneven or sloping at the landing site.

I am not talking about the Lunar configuration. The doughnut and the rocket body would be safely protected behind an ablative shield of the required size.

Is there any limit to the size of a saucer shaped ablative shield?

If not, then the Mars lander you have already designed can be equipped with a doughnut cargo carrier, and you will have instantly solved the elevator problem that our friends in Germany were worried about.

After aerobraking, the center of the heat shield would eject, exposing the rocket engines, and they would complete the vertical landing.

After landing, the entire doughnut assembly would disconnect from the delivery rocket, and it could return to orbit, with fuel in the tanks due to placing cargo outside.

If Void were willing to do some of his artwork for us, he could show the saucer shaped heat shield first in descent, followed by the rocket body enclosed in the cargo doughnut.

This image might be helpful for those who are attempting to follow the discussion.

(th)

Offline

#360 2024-08-03 16:29:59

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Standing the vehicle and doughnut upon a heat shield might work,  given some sort of insulation and high-temperature skin for the doughnut and vehicle.  That is a heavy solution,  though.  More so at Earth than at Mars.  The worst case entry speed at Mars is about 7.5 km/s,  pretty close to orbital entry speed (8 km/s) here at Earth.  You are talking exposure of doughnut and vehicle to gas near 7500-8000 K in such circumstances,  but without the harsh scrubbing effects. Mercury and Gemini did that as bare metal afterbodies,  but with serious insulation between those exposed afterbody skins and the pressure shell of the cabin.

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#361 2024-08-03 17:25:22

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson re #360

Thanks for considering the saucer shaped heat shield idea.

The heat shield would take the brunt of the heating, so I assume ??? your concern is that hot gases would swirl behind the heat shield and into the low pressure region where the cargo and ship are hiding.

This problem has been successfully addressed for many decades.

It is possible (indeed likely) I just don't understand something important.

Perhaps the technique that has protected capsules returning to Earth from orbit or from the Moon only works at small scale?

Or perhaps the concern might be the length of the rocket, which might well extend into the wake of the oncoming atmosphere, after it exits the heat shield?

In any case, this is an interesting discussion and I hope it may be useful for Mars mission planners.

(th)

Offline

#362 2024-08-04 09:47:59

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

What happens on leeside separated-flow surfaces has the same driving temperature as the heat shield out front,  but a far lower heat transfer coefficient,  because the weakly moving fluid does not scrub the surface.  Scrubbing raises heat transfer coefficients,  quite dramatically.  By around a factor of 10 between separated wakes and heat shield front sides in terms of heating rates.  Heating rate is the area times the heat transfer coefficient times the driving temperature difference.

That wake zone heating rate reduction makes the wake-zone heating rate more nearly the same as the heat re-radiation rate of "dark" surfaces at practical temperatures near 1000-2000 F.  That is true for Earth entry up to about 8 km/s,  but no faster:  the gas temperatures get too high,  in turn driving up heating by convection rates,   and re-radiation cannot keep up at the surface temperatures that known materials can withstand.  The re-radiation is proportional to absolute surface material temperature raised to the 4th power!

That balance of effects is why the old Mercury and Gemini capsules had ablative heat shields,  but bare metal backside surfaces.  They never exceeded about 8 km/s at entry,  and re-radiation could keep pace with the convective input,  albeit only for rather exotic alloys.  You can do it with stainless steel these days,  at least in large sizes.  However,  there must be some sort of high temperature-capable insulation between that hot leeside skin and the capsule pressure shell within.  The hot skin re-radiates both directions,  if there is not.   You cannot do this with fiberglass,  it melts at 900 F.  Has to be mineral wool capable of withstanding 1500-2000 F.

Apollo came back from LEO at the same 8 km/s speeds,  but from the moon much faster (about 10.9 km/s).  With convective heating proportional to velocity cubed,  and plasma radiation (from about 9 km/s on up) even a higher power,  the total heating is way more than factor 2.5+ greater.  Apollo had the ablative heat shield,  but it had the same ablative as a thinner layer all over its backside surfaces,  too. 

In addition to the higher driving temperatures far-outracing the re-radiation effect,  the more brightly-glowing plasma sheath is becoming pretty much opaque to thermal re-radiation,  cutting off that method of cooling entirely by about 11 km/s speeds.

You can estimate (crudely) the gas driving temperatures for convection,  anywhere around the capsule including backside separated wake zones,  quite simply.  The effective gas temperature in degrees K is numerically equal to the flight speed in m/s.  That's about a 10%-good estimate.  Actual values are higher or lower by up to 10%,  because of varying ionization-level effects.  Yet,  at 8 km/s = 8000 m/s bringing about 8000 K gas temperatures,  who really cares about 10% error?  The real point is,  it's overwhelming.  At 11 km/s,  it's pretty near 11,000 K,  etc. 

There are no materials that can stand such exposures steady-state.  Only on a short transient,  and only if cooled somehow,  by re-radiation and/or ablation.  Above about 9-10 km/s,  only by ablation.  Theoretically,  transpiration cooling might also work,  but it has never been flown,  and so is unproven as of yet.

GW

Last edited by GW Johnson (2024-08-04 09:53:33)


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#363 2024-08-04 11:26:37

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson re #362

http://newmars.com/forums/viewtopic.php … 51#p225551

SearchTerm:HeatShield Heat Shield operation at various temperatures

In particular, this post includes explanation of the use of ablative material on the back side of the Apollo Moon Return vehicle to deal with hot gases flowing from the front of the capsule, around the rim, and into the region behind the vehicle.

For GW:

Picking up on your explanation of how the Apollo capsules were designed to survive Moon return, was the Orion capsule designed in the same or a similar way?

And ... is it safe to assume that if SpaceX attempts to return from the Moon directly, it must have ablative material around the entire vehicle?

And ... is it safe to assume that if ** anyone ** tries to return from Mars depending upon aerobraking, they will be subject to the same principles, except to a more extreme degree?

(th)

Offline

#364 2024-08-04 14:08:12

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

To answer your questions ---

Picking up on your explanation of how the Apollo capsules were designed to survive Moon return, was the Orion capsule designed in the same or a similar way?    YES

And ... is it safe to assume that if SpaceX attempts to return from the Moon directly, it must have ablative material around the entire vehicle?    YES

And ... is it safe to assume that if ** anyone ** tries to return from Mars depending upon aerobraking, they will be subject to the same principles, except to a more extreme degree?   YES

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#365 2024-08-04 19:30:33

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson re #364

Thank you for those definitive answers!

***
kbd512 came up with a name I'd like to pass along: Xyla Foxlin
American engineer and entrepreneur

SearchTerm:follower Xyla Foxlin

Please Google that lady.  She graduated from Case Western.  She has nearly half a million followers.

kbd512 thinks the kind of person we are looking for would be about 1 in 10,000.

With a population of 8 billion, that would be 800,000 potential persons with the needed set of abilities and interests.

However, that number would include all ages and all nations.

The number of candidates in the US who are below 20 would be some small fraction of that larger number.

(th)

Offline

#366 2024-08-05 15:48:53

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

I looked at the gal Kbd512 came up with.  Impressive for one so young. 

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#367 2024-08-08 12:26:55

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

If everything works, this post will contain a link to an image of a revision of GW's Mars Lander concept.

GW Johnson evaluated Void's Cargo Ring idea, and pronounced it ** good ** for an airless landing. However, complications of trying to descent through atmosphere at Mars led GW to this Splayed Toes version. The basic idea is preserved... the cargo is mounted outside the rocket, and it is deployed to the surface directly, instead of having to be unloaded from the rocket.

SAG6I7x.png

(th)

Offline

#368 2024-08-09 09:39:12

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Not sure where to put all this stuff:

From AIAA’s “Daily Launch” for 8-9-2024:

ARS TECHNICA

A new report finds Boeing’s rockets are built with an unqualified work force

The NASA program to develop a new upper stage for the Space Launch System rocket is seven years behind schedule and significantly over budget, a new report from the space agency's inspector general finds. There is also some information about the project's prime contractor, Boeing, and its quality control practices. "We found an array of issues that could hinder SLS Block 1B’s readiness for Artemis IV including Boeing’s inadequate quality management system, escalating costs and schedules, and inadequate visibility into the Block 1B’s projected costs," states the report, signed by NASA's deputy inspector general, George A. Scott.

My take:  why is that a surprise to anyone?  At this rate,  there never will be an SLS Block 1B or a Block 2.
SPACENEWS

Chinese megaconstellation launch creates field of space debris


A Chinese launch to deploy a first batch of communications satellites has created more than 50 pieces of debris which could threaten spacecraft in low Earth orbit. The Long March 6A launched Aug. 6, from a specifically constructed launch pad at Taiyuan spaceport. The rocket’s upper stage, modified for restarts and deploying numerous satellites, deployed 18 flat panel Qianfan (“Thousand Sails”), or G60, satellites into roughly 800-kilometer-altitude polar orbit for Shanghai Spacecom Satellite Technology (SSST).

My take:  a cultural attitude developed over millennia is showing through.  They behave irresponsibly unless forced to behave responsibly.  It’s just part of the bullying hierarchy thing.


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#369 2024-08-09 11:00:36

kbd512
Administrator
Registered: 2015-01-02
Posts: 7,774

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

GW,

If we don't clean up our engineering practices here at home, and all the messes the Chinese and Russians have created in space, then nobody ever will, simple as that.  Contrary to what we've been led to believe, the Chinese don't think too far ahead.  The "One Child" policy is proof-positive of that.  More than half of all Chinese people are now approaching or over the age of 50.  Their government now admits they over-counted all the people under age 40 to the tune of about 200 million people.  Their society is rapidly aging out existence due to their own shortsightedness.  There's nothing anyone who is not Chinese could ever do about that.  Demographics is destiny.

Offline

#370 2024-08-09 14:27:20

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Kbd512:

Actually,  I quite agree with you about China.  I would only add that communism just made those same faults even worse,  pretty much the same way it did in Russia.  Naziism and fascism did the very same things in Germany and Italy.  Supposedly,  those ideologies are polar opposites.  My thesis:  no they are not!  Not really,  in any observable objective way!

Far left,  far right,  I see no real objectively-observable difference!  They both end up with leader-cult dictators held in place with military force,  oppressing all under their sway,  and neighbors,  too.  Their words don't matter!  Only their actions do! 

The political spectrum is NOT linear (as everybody conceives),  it is in fact a circle,  with 2 "different" ways to end up on the dictatorship side (one using far-left words,  the other using far-right words).  Which is EXACTLY why the words they spout do NOT matter,  while their ACTIONS mean everything!  The evil that starts the process around the circle to the dictatorship side,  by either way,  is extremism.  Pure and simple.  Extremism,  be it political or religious or both,  is the true evil that Satan has let loose in this world. 

As for US politicians,  throughout our history,  you can easily tell when they lie:  their lips are moving!  Left,  right,  doesn't matter.  Politicians are like diapers,  they need changing often,  and for exactly the same reason.  So said Mark Twain.  And he was quite right!  Do NOT listen to the words!  Look at the actions!

Engineering-wise:  there needs to be an objective assessment of what a project is really all about:  excellence or profit?  If profit,  what are the legal and ethical constraints that you MUST observe?  If excellence,  how much can we currently do,  and still profit in some way?  THOSE are the questions nobody asks or answers anymore!  And it is really beginning to show!  Not just at Boeing!

GW

Last edited by GW Johnson (2024-08-09 14:44:14)


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#371 2024-08-10 16:55:22

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

For GW Johnson about patent search for spacecraft landing systems...

The USPO appears to be offering a new and updated search tool.  I tried the tool with a search for "landing" and "legs" and got 468 pages of results, few (if any) appeared to have anything to do with spacecraft.

SpaceX ** must ** patented the landing system they are using for Falcon 9. That would have been an elementary defense against the inevitable patent trolls.  I'm interested in seeing their patent(s) in this area, to see if it extends to Void's cargo landing idea.

https://ppubs.uspto.gov/pubwebapp/stati … basic.html

(th)

Offline

#372 2024-08-10 20:10:52

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

This is a follow up on Post #371...

I went back to the USPO site and tried again. This time I used "spacex" and "legs"

The first item is this one:

Result #    Document/Patent number    Display    Title    Inventor name    Publication date    Pages
1    US-20240228068-A1       PDF   Text    PROPULSIVE LANDING ROCKET LANDING LEG SYSTEM, AND METHODS OF MAKING AND USING THE SAME    Balaj; Arist    2024-07-11    27

There is an illustration that looks a lot like the Falcon 9 landing leg system.

(th)

Offline

#373 2024-08-12 08:21:23

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

I sold and delivered my 15th ramjet book yesterday. 

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

#374 2024-08-12 08:44:19

tahanson43206
Moderator
Registered: 2018-04-27
Posts: 18,928

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

Congratulations on sales of the ramjet book!

For those in the readership who may wish to obtain information about the book:

text to be provided

(th)

Offline

#375 2024-08-15 09:27:12

GW Johnson
Member
From: McGregor, Texas USA
Registered: 2011-12-04
Posts: 5,736
Website

Re: GW Johnson Postings and @Exrocketman1 YouTube videos

In a different topic,  I hear that SpaceX has re-opened the tower test stand at McGregor,  after it was damaged by some kind of fire incident.  Literally,  I hear it. 

GW


GW Johnson
McGregor,  Texas

"There is nothing as expensive as a dead crew,  especially one dead from a bad management decision"

Offline

Board footer

Powered by FluxBB